Hubbardton-forge 365615 Manual de usuario descargar pdf

Installation Instructions A197

For Outdoor Chain Hung Fixture 36-5615 & 36-5615F Page 1 of 2

Hand-Forged, Vermont-Made Lighting and Accessories

P.O. Box 827, 154 Route 30 South, Castleton, Vermont 05735

22646

To Install Fixture (Figure 1)

Component Parts

A Lock Nut

B Crossbar

C Threaded Stud (2)

D Nipple

E Wood Screws (4)

F Canopy

G Canopy Loop

H Cover Plate

I Knurl Ball (2)

J Chain

K Fixture Loop

L Fixture Top

M Retaining Ring (2) (“F” version has only 1

retaining ring)

N 8-32 x 3/8” Screws (3)

O 8-32 x 1” Screws (3)

P Spider Assembly

Q Washer

Caution: Be sure power is off at the main breaker box prior to installation

1. Carefully unpack the fixture from the carton.

2. Remove glass retaining rings (M) and put aside and save for later use.

3. Loosen screws (O) that are shipped installed in threaded bosses on underside of

fixture next to socket and remove washer (Q) by turning clockwise to slip over

heads of screws. Loosen screws until there are only a couple threads engaged

with the threaded bosses.

4. Loosen screws (N) so that spider assembly (P) will turn clock wise. It is not

necessary to completely remove screws (N) from fixture. Once spider assembly

(P) is loose turn until it slips over the heads of the screws. Set aside for later use

(Figure 2).

5. Thread studs (C) through appropriate holes in crossbar (B) to match holes in

canopy (F).

6. Thread canopy loop (G) onto nipple (D).

7. Thread the nipple (D) into the crossbar (B) and secure with lock nut (A).

8. Attach one end of the chain to the fixture loop (K). Lace the wire through

every other link of the chain (J) to the end.

9. Slide cover plate (H) and canopy (F) over chain (J) until they rest against

fixture top (L).

10. Fasten the chain to the canopy loop (G) and slip wires through the canopy

loop (G) and nipple (D). Make sure to provide enough slack in the wire to

ensure weight of fixture is supported by the chain.

11. Raise fixture to ceiling and using at least two wood screws (E) attach cross

bar (B) to a structural member in the ceiling, centering the crossbar over the

outlet box. We've supplied wood screws with your fixture; however, different

materials and/or construction methods may require different fasteners. If in doubt,

contact a qualified electrician. Do not attach crossbar directly to outlet box.

(continued)

CAUTION: FAILURE TO INSTALL THIS FIXTURE PROPERLY MAY RESULT IN SERIOUS PERSONAL

INJURY OR DEATH AND PROPERTY DAMAGE. We recommend installation by a licensed electrician.

This product must be installed in accordance with applicable installation code(s), by a person familiar with the

construction and operation of the product and the hazards involved.*

Caution: Do not exceed maximum wattage noted on fixture. Use only recommended bulbs with fixture.

(Figure 1)

(Figure 2)

1 2

A197 1
22646 1

Indice de contenidos

Pagina 1 - 22646

Installation Instructions A197 For Outdoor Chain Hung Fixture 36-5615 & 36-5615F Page 1 of 2 Hand-Forged, Vermont-Made Lighting and Accessor

Pagina 2

Installation Instructions A197 For Outdoor Chain Hung Fixture 36-5615 & 36-5615F Page 2 of 2 Hand-Forged, Vermont-Made Lighting and Accessor

Comentarios a estos manuales

Sin comentarios

Hubbardton-forge 365615 Manual de usuario

Busca en linea o descarga Manual de usuario para Encendiendo Hubbardton-forge 365615. Hubbardton Forge 365615 User Manual Manual de usuario

Indice de contenidos

Comentarios a estos manuales

Relacionado con productos y manuales para Encendiendo Hubbardton-forge 365615